VTM48ET040M050A00【PDF 13/18 页】VTM CURRENT MULTIPLIER 4V 50A

您好，
买卖IC网欢迎您。
请登录
免费注册

9页 10页 11页 12页 [13页]14页 15页 16页 17页

VTM 48 E x 040 y 050A00

12.0 INPUT AND OUTPUT FILTER DESIGN

A major advantage of a SAC TM system versus a conventional

PWM converter is that the former does not require large

functional filters. The resonant LC tank, operated at extreme

high frequency, is amplitude modulated as a function of input

voltage and output current and efficiently transfers charge

through the isolation transformer. A small amount of

capacitance embedded in the input and output stages of the

module is sufficient for full functionality and is key to achieving

high power density.

This paradigm shift requires system design to carefully evaluate

external filters in order to:

1.Guarantee low source impedance.

To take full advantage of the VTM TM module dynamic

response, the impedance presented to its input terminals

must be low from DC to approximately 5 MHz. Input

capacitance may be added to improve transient

performance or compensate for high source impedance.

2.Further reduce input and/or output voltage ripple without

sacrificing dynamic response.

Given the wide bandwidth of the VTM module, the source

response is generally the limiting factor in the overall

system response. Anomalies in the response of the source

will appear at the output of the VTM module multiplied

by its K factor.

3.Protect the module from overvoltage transients imposed

by the system that would exceed maximum ratings and

cause failures.

The V ? I Chip TM module input/output voltage ranges must

not be exceeded. An internal overvoltage lockout function

prevents operation outside of the normal operating input

range. Even during this condition, the powertrain is

exposed to the applied voltage and power MOSFETs must

withstand it.

13.0 CAPACITIVE FILTERING CONSIDERATIONS

FOR A SINE AMPLITUDE CONVERTER TM

It is important to consider the impact of adding input and

output capacitance to a Sine Amplitude Converter on the

system as a whole. Both the capacitance value and the

effective impedance of the capacitor must be considered.

A Sine Amplitude Converter has a DC R OUT value which has

already been discussed in section 11. The AC R OUT of the

SAC contains several terms:

? Resonant tank impedance

? Input lead inductance and internal capacitance

? Output lead inductance and internal capacitance

The values of these terms are shown in the behavioral model in

section 11. It is important to note on which side of the

transformer these impedances appear and how they reflect

across the transformer given the K factor.

The overall AC impedance varies from model to model. For

most models it is dominated by DC R OUT value from DC to

beyond 500 KHz. The behavioral model in section 11 should be

used to approximate the AC impedance of the specific model.

Any capacitors placed at the output of the VTM module reflect

back to the input of the module by the square of the K factor

(Eq. 9) with the impedance of the module appearing in series.

It is very important to keep this in mind when using a PRM TM

regulator to power the VTM module. Most PRM modules have

a limit on the maximum amount of capacitance that can be

applied to the output. This capacitance includes both the PRM

output capacitance and the VTM output capacitance reflected

back to the input. In PRM remote sense applications, it is

important to consider the reflected value of VTM output

capacitance when designing and compensating the PRM

control loop.

Capacitance placed at the input of the VTM module appear to

the load reflected by the K factor with the impedance of the

VTM module in series. In step-down ratios, the effective

capacitance is increased by the K factor. The effective ESR of

the capacitor is decreased by the square of the K factor, but

the impedance of the module appears in series. Still, in most

step-down VTM modules an electrolytic capacitor placed at the

input of the module will have a lower effective impedance

compared to an electrolytic capacitor placed at the output. This

is important to consider when placing capacitors at the output

of the module. Even though the capacitor may be placed at

the output, the majority of the AC current will be sourced from

the lower impedance, which in most cases will be the module.

This should be studied carefully in any system design using a

module. In most cases, it should be clear that electrolytic

output capacitors are not necessary to design a stable,

well-bypassed system.

Rev. 3.2

V?I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200

2/2011

Page 13 of 18

v i c o r p o w e r. c o m

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

VTM48ET120M025A00 VTM CURRENT MULTIPLIER 12V 25A

VTM48FH060M020A00 HALF-CHIP VTM CURRENT MULTIPLIER

VY2682M59Y5US6TV7 CAP CER 6800PF 300V 20% RADIAL

W1X223MCVCP0KR CAP CER 0.022UF 275V 20% RADIAL

W2H11A2218AT1F CAP FEEDTHRU 220PF 100V NP0 0805

W3A4ZC224KAT2A CAP ARRAY 4CH 0.22UF 10V 0612

W3F15C4728AT1F CAP FEEDTHRU 4700PF 50V X7R 1206

W3L16C225KAT1A CAP CER 2.2UF 6.3V 10% X7R 0612

相关代理商/技术参数

VTM48ET040T050A00 功能描述:VTM CURRENT MULTIPLIER 4V 50A RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48ET120M025A00 功能描述:VTM CURRENT MULTIPLIER 12V 25A RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48ET120T025A00 功能描述:VTM CURRENT MULTIPLIER 12V 25A RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48FH060_020A00 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTMa?￠Current Multiplier

VTM48FH060M020A00 功能描述:HALF-CHIP VTM CURRENT MULTIPLIER RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48FH060T020A00 功能描述:CONVERT DC/DC VTM 5V 20A SMD RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM4ACD 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:One Shot (Latching Interval) Timing Module

VTM500F 制造商:Promise Technologies 功能描述:FG.VTRAKM500F.BOX.US/ASIA/EUROPE.PROMISE.WITH ROHS EXEMPTION - Bulk